donofrio's blog

Linux version 2.6.12-12mdksmp (apatard@n1.mandriva.com) (gcc version 4.0.1 (4.0.1-5mdk for Mandriva Linux release 2006.0)) #1 SMP Fri Sep 9 17:43:23 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff75000 (usable)
BIOS-e820: 000000007ff75000 - 000000007ff77000 (ACPI NVS)
BIOS-e820: 000000007ff77000 - 000000007ff98000 (ACPI data)
BIOS-e820: 000000007ff98000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
On node 0 totalpages: 524149
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 294773 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000febc0
ACPI: RSDT (v001 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd4d9
ACPI: FADT (v001 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd511
ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffefa6f
ACPI: MADT (v001 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd585
ACPI: BOOT (v001 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd609
ACPI: ASF! (v016 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd631
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled)
Processor #6 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] enabled)
Processor #7 15:2 APIC version 20
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[24])
IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47
ACPI: IOAPIC (id[0x0a] address[0xfec80800] gsi_base[48])
IOAPIC[2]: apic_id 10, version 32, address 0xfec80800, GSI 48-71
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 3 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 80000000:7ec00000)
Built 1 zonelists
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec80000)
mapped IOAPIC to ffffa000 (fec80800)
Initializing CPU#0
Kernel command line: auto BOOT_IMAGE=linux root=305 resume=/dev/hda1 splash=silent
bootsplash: silent mode.
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2791.980 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2073024k/2096596k available (2451k kernel code, 22424k reserved, 788k data, 296k init, 1179092k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5521.40 BogoMIPS (lpj=2760704)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found.
CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
Enabling SMP...
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop... 5570.56 BogoMIPS (lpj=2785280)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
Booting processor 2/6 eip 3000
Initializing CPU#2
Calibrating delay loop... 5570.56 BogoMIPS (lpj=2785280)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel P4/Xeon Extended MCE MSRs (12) available
CPU2: Thermal monitoring enabled
CPU2: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
Booting processor 3/7 eip 3000
Initializing CPU#3
Calibrating delay loop... 5570.56 BogoMIPS (lpj=2785280)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel P4/Xeon Extended MCE MSRs (12) available
CPU3: Thermal monitoring enabled
CPU3: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
Total of 4 processors activated (22233.08 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 4 CPUs: passed.
Enabling SMP...
Brought up 4 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000003
groups: 00000001 00000002
domain 1: span 0000000f
groups: 00000003 0000000c
CPU1 attaching sched-domain:
domain 0: span 00000003
groups: 00000002 00000001
domain 1: span 0000000f
groups: 00000003 0000000c
CPU2 attaching sched-domain:
domain 0: span 0000000c
groups: 00000004 00000008
domain 1: span 0000000f
groups: 0000000c 00000003
CPU3 attaching sched-domain:
domain 0: span 0000000c
groups: 00000008 00000004
domain 1: span 0000000f
groups: 0000000c 00000003
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 183k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbdda, last bus=5
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1.PCI2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1.PCI3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 9 10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:07: ioport range 0x800-0x85f could not be reserved
pnp: 00:07: ioport range 0xc00-0xc7f has been reserved
pnp: 00:07: ioport range 0x860-0x8ff could not be reserved
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1137141406.557:0): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
vesafb: framebuffer at 0xf4000000, mapped to 0xf8880000, using 3750k, total 65472k
vesafb: mode is 800x600x16, linelength=1600, pages=67
vesafb: protected mode interface info at c000:59b2
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 34430 bytes,<6>...found (800x600, 34382 bytes, v3).
Console: switching to colour frame buffer device 93x30
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 112
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: WDC WD800BB-55JKA0, ATA DISK drive
hdb: _NEC DVD+RW ND-1100A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SAMSUNG CDRW/DVD SM-332B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
PDC20269: IDE controller at PCI slot 0000:05:0d.0
ACPI: PCI Interrupt 0000:05:0d.0[A] -> GSI 21 (level, low) -> IRQ 21
PDC20269: chipset revision 2
PDC20269: ROM enabled at 0xff300000
PDC20269: 100% native mode on irq 21
ide2: BM-DMA at 0xccc0-0xccc7, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xccc8-0xcccf, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: WDC WD1200JB-75CRA0, ATA DISK drive
hdf: WDC WD1200JB-75CRA0, ATA DISK drive
ide2 at 0xccf8-0xccff,0xccf2 on irq 21
Probing IDE interface ide3...
hdg: SAMSUNG CDRW/DVD SM-332B, ATAPI CD/DVD-ROM drive
ide3 at 0xcce0-0xcce7,0xccda on irq 21
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
hde: max request size: 128KiB
hde: Host Protected Area detected.
current capacity is 234375000 sectors (120000 MB)
native capacity is 234441648 sectors (120034 MB)
hde: Host Protected Area disabled.
hde: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hde: cache flushes not supported
/dev/ide/host2/bus0/target0/lun0: p1
hdf: max request size: 128KiB
hdf: Host Protected Area detected.
current capacity is 234375000 sectors (120000 MB)
native capacity is 234441648 sectors (120034 MB)
hdf: Host Protected Area disabled.
hdf: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hdf: cache flushes not supported
/dev/ide/host2/bus0/target1/lun0: p1 p2
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
NET: Registered protocol family 1
Starting balanced_irq
ACPI wakeup devices:
VBTN PCI0 USB0 USB1 USB2 PCI1 PCI2 PCI3 PCI4 KBD
ACPI: (supports S0 S1 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
input: AT Translated Set 2 keyboard on isa0060/serio0
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 296k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ff80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ff60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
hub 3-0:1.0: USB hub found
usb 1-2: new low speed USB device using uhci_hcd and address 2
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa20000
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usbcore: registered new driver hiddev
usbhid: probe of 1-2:1.0 failed with error -5
usbcore: registered new driver usbhid
usb 1-2: USB disconnect, address 2
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
usb 1-2: new low speed USB device using uhci_hcd and address 3
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-2
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
EXT3 FS on hda5, internal journal
Adding 4184892k swap on /dev/hda1. Priority:-1 extents:1
Non-volatile memory driver v1.2
hw_random: RNG not detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel E7505 Chipset.
agpgart: AGP aperture is 128M @ 0xe0000000
Supermount version 2.0.4 for kernel 2.6
ntfs: Ignoring new-style parameters in presence of obsolete ones
NTFS driver 2.1.22 [Flags: R/O DEBUG MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
loop: loaded (max 8 devices)
hdb: ATAPI 32X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: irq timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hdb: DMA disabled
hdb: ATAPI reset complete
hdc: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
hdg: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache